Phone: 918-234-8665

Used Parts Washers

Washer Sales. Washer Buyers. Washer Service & Repair

Home/Brands/Stoelting/Stoelting 24×18 Stainless 3 Stage with Heated and Ambient Blow-Off Omniforce OMF-324

Stoelting 24×18 Stainless 3 Stage with Heated and Ambient Blow-Off Omniforce OMF-324

Model No. OMF-324 

S/N 0296-0603

Amazing Condition with light usage.

Originally built to clean Diesel Engine Components.

Equipped with Higher Horsepower than most standard Pass Through Washers.  

(5) Total Stages

  • (1)  7’, Tank 450 Gallons 175 GPM Gusher 15 HP Pump 140 Deg. F. Gas Heat 380,000 BTU, Tank Fill ¾” NPT, Over Flow 2” NPT, Drain 2” NPT, Filter 10 Micron
  • (2)  7’, Tank 450 Gallons 175 GPM Gusher 15 HP Pump 140 Deg. F. Gas Heat 380,000 BTU, Tank Fill ¾” NPT, Over Flow 2” NPT, Drain 2” NPT, Filter 10 Micron
  • (3)  7’, Tank 450 Gallons 175 GPM Gusher 15 HP Pump 140 Deg. F. Gas Heat 380,000 BTU, Tank Fill ¾” NPT, Over Flow 2” NPT, Drain 2” NPT, Filter 5 Micron
  • (4)  9’, Dryer 2500 CFM, 15 HP, 250 Deg. F., Gas 500,000 BTU, 5” NPT
  • (5)  5’, Ambient 1100 CFM, 5 HP, 5” NPT 

Removable Access Doors On Each Stage. (2) On Heated Dryer Stage

 Materials of Construction:

  • Tanks: 12 Guage 304 Stainless Steel
  • Canopies: 14 Gauge 304 Stainless Steel
  • Frame Under Tanks: Carbon Steel
  • Exterior Plumbing: Stainless Steel
  • Interior Plumbing: Stainless Steel
  • Chip Baskets Stainless Steel
  • Recirculating Pumps: Stainless Steel Fitted
  • Conveyor Frame: 10 Gauge Stainless Steel
  • Conveyor Belt: Stainless Steel
  • Conveyor Rollers: Stainless Steel

Product Clearance:

  • Conveyor Belt 24” Wide by 18” High

Conveyor Drive:

  • ¾ hp drive is variable speed, rated for 100lbs./linear foot
  • Speed potentiometer on operator panel to control the conveyor speed, 20-12 feet per minute, standard.
  • Conveyor start/stop button on operator control panel
  • E-stops on load and unload sections
  • Product jam sensing with current sensing relay

Solution Recirculation:

  • Efficient Recirculation System channels 100% of pumped solution through a stainless steel chip/product catch basket, screen water coming off of the shed sheet
  • Weir and baffles for sludge and oil entrapment

 Solution Spray System:

  • The solution spray system utilizes spray tubes of the exclusive Stoelting Fixed Spray Design
  • This design allows for wash solution to effectively clean through a combination of solution impingement and chemical action
  • The Stoelting Spray Tubes have a specially designed orifice that produces a “spray nozzle type” spray but does not require the maintenance of replacing nozzles
  • The Spray tube can easily be removed from the machine and quickly cleaned by the use of a bristle brush.
  • Spray tubes are located above, below and on both sides of the spray tunnel for highly effective 360º washing action
  • The “Spray Zone” of wash section is 4’ long and of the rinse section is 2’
  • Top and bottom spray pressure is individually adjustable with manual ball valve and pressure gauge

Blow Off Sage (s) 

Heated Blow Off – Electric

  • Nine (9) foot long insulated tunnel construction
  • 15 HP blower, 2500CFM rated
  • air knives that are located on the top and bottom of each side of the conveyor, depending on product configuration
  • Top and side air knives are adjustable for optimal performance
  • Air temperature is monitored and controlled with a digital set point controller
  • Blower start and stop push buttons and heat on/off selector switch included with safety electrical interlock

Sound Barrier

  • Barrier lined with sound absorbing foam
  • Surround blower on dryer and/or ambient blow off

Remoter Start/Stop-Conveyor:

  • Conveyor start/stop buttons can be placed at load/unload end of washer
  • Allows conveyor to be started and stopped independently of other washer operations

Common Support Frame:

  • Carbon steel tubular frame for common support of wash system

Utilities:

  • Incoming Water
  • Nominal 40 PSI
  • Maximum 125 PSI
  • Note: Soft Water Recommended

Electrical:

  • 460 Volt 3 Phase, 60 HZ

Canopy Venting:

  • 6” Pipe Flange Connection
  • All Joints to be Water Tight
  • Equivalent Length of Ducting 25 Ft. Max

Natural Gas:

  • 1500 CF/HR (Approx) @ High Fire
  • Customer to Supply Incoming Gas Regulator to Insure 22” WC
  • At Gas Inlet – 1-1/2” Inlet Piping

Lifting Instructions:

  • *Lifting Points
  • Lift Machine Using Chain at Indicated Lifting Points with Spreader Bar to
  • Prevent damage to machine.

Sold Loaded on Truck,  Detroit, MI      

 

 

Leave a Comment